久亚洲一线产区二线产区三线产区,国产伦精品一区二区三区视频,一本久久a久久精品vr综合,最近2019年日本中文免费字幕

銷售咨詢熱線
15953126901
15153196527
公司新聞 hengye
企業案例 case

聯系我們

  • 聯系人:濟南燕翔鐵藝制品有限公司
  • 手機:15953126901
  • 電話:15153196527
  • 郵箱:785385551@qq.com
  • 地址:濟南市天橋區歷山北路黃臺不銹鋼市場3區317
當前位置: 首頁 > 新聞資訊>公司新聞

帶您了解鐵藝大門的焊接工藝

來源:http://m.nbsdzs.com 日期:2024-04-11 發布人: 瀏覽次數:1

1、邊框焊接,按邊框尺寸在地上定位。將邊框料的兩端寬邊上切成45。對接后點焊。校正無誤<方框的對角線要相等)后焊牢。

1. Weld the frame and position it on the ground according to the size of the frame. Cut the wide edges of both ends of the border material into 45 pieces. Spot welding after docking. Correctly correct (the diagonal of the box should be equal) and then weld it firmly.

2、中間長豎管焊接,每扇門3根長豎管,均勻分布在邊框內,定位間距為339毫米。擺放好位置后,先點焊,再校平,檢查無誤后再焊牢。

2. The middle long vertical pipe is welded, with 3 long vertical pipes for each door evenly distributed within the frame, with a positioning spacing of 339 millimeters. After placing it in place, spot weld it first, then level it, check for accuracy, and then weld it firmly.

20230330104624723.jpg

3、矛頭用橫管焊接每扇門4根,夾在中問長豎竹之間、擺放好位置后,先點焊,再校平,檢查無誤后再焊牢:

3. The spear head is welded with a horizontal pipe, with 4 pieces per door, sandwiched between the long and vertical bamboo in the middle, and placed in the correct position. After spot welding, leveling, and checking for accuracy, it is welded firmly:

4、中間短豎管焊接,侮扇門4根,按圖樣中的位置擺好。先點焊,再校平,檢查無誤后再焊牢。

4. Weld the short vertical pipe in the middle, and place 4 doors according to the position in the drawing. First spot weld, then level, check for accuracy, and then weld firmly.

5、短橫管焊接每扇門24根,按圖樣中的位置擺好。先點焊,再校平,檢查無誤后再焊牢。為防l上焊接變形,可問隔焊。由于順序打亂,焊點較多,焊完后應檢查有無漏焊部位。

5. Weld 24 short horizontal pipes to each door and arrange them according to the position in the drawing. First spot weld, then level, check for accuracy, and then weld firmly. To prevent welding deformation on L, it is possible to ask for welding isolation. Due to the disordered sequence and a large number of welding points, it is necessary to check for any missed welding areas after welding.

6、槍頭焊接依次將各槍頭分別焊在相應的位置上,要求與橫桿垂直,正面朝前,不能扭曲。

6. Weld the gun heads in their respective positions in sequence, ensuring they are perpendicular to the crossbar, facing forward, and not twisted.

7、花形焊接把所有花形分別擺放在相應位置上,看是否合適,調整無誤后,先點焊到框架上,整體再檢查一遍,然后焊牢。

7. Flower welding: Place all flower shapes in their respective positions to see if they are suitable. After adjusting them correctly, spot weld them onto the frame first, inspect the overall structure again, and then weld them firmly.

天天做天天摸天天爽天天爱| 久久九九精品99国产精品| 亚洲丰满多毛的隂户| 精品无码久久久久久久动漫| 含一整夜 好涨h| 天堂а√在线中文在线| 国产综合无码一区二区辣椒| 亚洲成AV人片在线观看无 | 宝贝把腿张得大一点就不痛了| 少妇AV一区二区三区无码| 五个丝袜女警榨精嗯啊哦哦| 野外做受又硬又粗又大视频| 在线观看亚洲AV日韩A∨| 强制高潮18xxxxhd日韩| 小雪第一次尝到了又粗又大视频| 艳妇臀荡乳欲伦交换h| 国产免费一区二区在线a片视频| 夜夜爽夜夜叫夜夜高潮漏水| 西西人体做爰大胆视频韩国 | 日本japanese丰满少妇| 亚洲最大中文字幕无码网站| 欧美黑人乱大交bd| 全是肉的高h短篇列车| 风韵少妇性饥渴推油按摩视频| 国产美女精品一区二区三区| 精品久久久无码中文字幕| 3d全彩无码啪啪本子全彩| 美女100%裸体无遮挡| 国产一区二三区好的精华液 | 午夜精品一区二区三区在线观看 | 国产97色在线 | 国产 | 狠狠躁18三区二区一区| 亚洲 自拍 另类 欧美 综合| 巜疯狂的少妇4做爰bd| 国产精品扒开腿做爽爽爽视频| 肥嫩多毛的大荫户| 出轨人妻被粗长征服过程| 嘟嘟嘟WWW免费高清在线直播| 朋友人妻翘臀迎接粗大撞击| 被多个强壮的黑人灌满精| 国产精品无码无片在线观看3d|